New Francois Vivier designed Yawl with Clint Chase

Francois Vivier and Clint Chase are busy designing a new dayboat/weekender. This has been a fun collaboration and we have a lot more work to do. By this time next year, it is planned that we will be building this boat in our shop for our family use and for showing in 2012. Francois's boats are designed with a CAD-CAM approach, meaning the drawings are done in the computer, files are generated, and these files can be used to do CNC cutting of all the drawn boat parts, such as bulkheads, molds, and planking. Some of the design requirements were:

· To be trailerable by an ordinary car, and therefore light, and be able to beach temporarily for loading/unloading.

· To have a large, wide and deep cockpit, comfortable, allowing for fishing and a place where children could be safe.

· To have a stable hull for family sailing but give excellent performance for weekend sails “with the guys”.

· To have a cuddy cabin, with a toilet for women and children, a small galley to heat some meals and two berths to spend a night or two on board, or for napping.

What I am most excited about is getting my kids out sailing again.

Free Goat Island Skiff Yawl Plan

Drake and family at the beach

Drake is getting built in the shop to test the fitting of the kit before they get shipped off to first customers in WA and PA. Kent Fosnes in WA will be exhibiting Drake next year at the Port Townsend Wooden Boat Festival. All kits are tested more than once to ensure everything goes together properly. Many of these CAD drawn, computer numerically controlled (CNC) parts are cut to the thousandth of an inch! Accuracy and precision are among a number of value added benefits to a kit. More info about CNC cutting and those benefits is forthcoming.

The first GIS Yawl doing the Texas 200 endurance event.

After the busy summer, I am back in action. Just finished are some plans for my GIS yawl that I am making available for free on my GIS page. Enjoy looking at the yawl and the other tidbits of info I include. Our GIS will be going together in October.

Day Three in Drake: The final day of the Small Reach Regatta

The final day was going to have big shoes to fill after an incredible reach and row day 2. The rowing group gathered at breakfast to scheme a separate rowing group to explore along MDI's north coast and down to Bar Harbor. We did just that with the generous support of the chase fleet whose member take very seriously there job to watch everyone, help us stay safe, and get us out of trouble when we need it. The sailing fleet (most of the boats) went to Bean Island just east of Hancock Point and the rowing group (5 boats) went south to Bar Island on an absolutely windless morning and a fast outgoing tide. After lunch on Bar, we had a rolicking return as the seabreeze turned on and was blowing a steady 15 kts. Drake shone again as we surfed down the white-capped, following sea. I had left the sailing rig ashore to be a pure rowboat today. The timing was perfect on the way back into Lamoine Harbor area: the entire sailing fleet was also returning. After a little racing in the rowboats, we coalesced into a parade of sails past the state park where onlookers marveled at the sight reminiscent of the age of sail when it was commonplace to see so many sails filling a waterfront view.

Learn more about the Small Reach Regatta

Small Reach Regatta: Day 2 in Drake Rowboat

I was a little nervous beginning day 2 on a long reach with a potentially gusty offshore breeze that would carry the fleet 8+ miles to the lunch stop. The cracked mast step was only glued back together last night. Would it hold? This was going to be the same tack that I was on when it snapped. I didn't want to ruin this sail!

While the rowboa

ts and sailboats waited for the whole fleet to be launched and hoist sail for the departure, I

lounged on the floorboards enjoying an egg sandwich made by the caterer who cooks for the event. The food is great and the camaraderie while dining is something I enjoy every year. I saved my sandwich for this moment, laying back on the thwarts in the morning sun watching all the sails around me skitter about waiting for the moment when the lead chase boat would say "every body is in, let's go!".

The sail was east to Flanders Bay where we were to lunch at a bar connecting Ash and Sheldrake Islands (family islands that I arranged for us to have as a lunch spot). The fleet sailed on port

tack on a beam reach for all 8 miles to the stop. It was a hoot to say the least. Drake was right up with all the Caledonia Yawls and other larger sail craft. People were quite surprised to see this long, skinny rowboat pass them or hold position next to boats with much larger sail areas. And to my delight the mast step held.

But this morning was proving something that I try to espouse whenever possible: a rowboat with at least some keel to it can sail downwind quite

fast, but not up wind. And you don't need to ruin

the lines of the boat for rowing and you do not need to add the complexity and drag that a centerboard or daggerboard introduces. Lee boards are simply not necessary for off the wind sailing. Drake has enough stability and keel to even sail without any slippage on a bean reach, and this was a revelation this morning on Frenchman Bay.

The lunch was quick as the tide was eating up the bar -- we arrived a little too late. But the scene was quite spectacular with MDI and Tunk mountain and islands all around. I was the first boat to the bar and the 50 or 60 boats sailing into the bar was just a blast to watch.

The return trip was a 8-mile row to windward, through Sorrento Harbor right by Hancock Point and dir

ectly to Lamoine State Park. Drake showed her stuff by being able to row a steady 4+ knots back to the start line and beat most of the sailboats that had to tack many times to get home. This is what she was designed to do: sail smartly off the wind and row efficiently upwind. If this were a real RAID I would have no doubt t

hat we could be very competitive and with a larger boat for two rowers, probably win. But I enjoy the autonomy, privacy, and relaxation that rowing and sailing alone can bring.

Drake in the Small Reach Regatta on the Coast of Maine: Day 1

The Small Reach Regatta was the next stop in my busy summer. The SRR is a gathering of 70 sail-and-oar boats, this year, at Lamoine State Park and put on by the Downeast Chapter of the Traditional Small Craft Association. Irowed and sailed (downwind) his rowboat design Drake and consistently finished in the front of the fleet (but of course it wasn’t a race!).

This event is an annual gathering and a wonderful chance to test and showcase the boats CCBB sells and builds to designs from around the world, for example Michael Storer in Australia, Francois Vivier in France, Eric Risch in Maine, Bruce Elfstrom's beauties and my own designs. We will be carrying kits and building boats produced by a Finnish builder, Suomen Puuvenepiste. These are unique, semi-exclusive agreements to bring new sailing and rowing boats into the US market as CNC cut kits, bare hulls, and finished boats up to 25 feet. My hope is to bring a demo boat from all these folks to boat shows and events like the SRR. Next year we'll have a Goat Island Skiff Yawl to show off like this one built by a kit customer in TX for the Texas 200:

The event was three days. Day 1 was a short windy upwind row and downwind return to a classic small Maine coast island. Every day features an interesting lunch stop, a wonderful opportunity to rest and to look at others' boats. Moreover, I see it as a learning experience to talk to the builders and owners of the boats. I learn something new from every one of the boats. For me, the SRR is about the finest form of professional development I can get.


On the downwind return to camp, a small squall came through and the force overcame my mast step..."WHAM!"...I heard the snap and the boat lurched and we nearly capsized. The first night was a quick repair with polyurethane glue while the sun set. Day two was to feature a long, fast broad reach to the lunch spot, and there was no way I was going to miss sailing that stretch! I was repairing until I couldn't see anymore boat...will it work?

Teaching at The Wooden Boat School: Tradional & Modern Oar Making

After work at Shaw and Tenney, I had my debut teaching job at Wooden Boat School. One of my favorite (and most labor intensive) specialties is oar making, so I was to teach the traditional way and the modern way, using composite blades. Each students chose an oar type of their choice to fit a boat they had or wanted to have. We had everything from 7' flat blade Spruce oars (for a Nutshell Pram) to laminated plywood spoon blade sculls to a Greenland style kayak paddle.

 

We were able to get out for two solid rows where CLint coached some fixed seat rowing and we all just enjoyed learning how to use oars and be comfortable in rowboats. We were able to use the school's fleet of rowboats, including this Joel White Shearwater.

 

Students quickly learned that oar making is mostly a wood removal activity, but they also learned some of my tricks, like adding decorative laminations on the outside of the upper looms. They also learned that there is a bit of engineering and art in making oars. Because we were able to get on the water, we also so the clear link between how we shape oars in the shop and how they react on the water.

 

Finishing oars after sanding is as much work as shaping them. One of my big pet-peeves is that oars are balanced and we spent a couple hours balancing everybody's oars with a little lead in the handle. It does not make the oar heavier, effectively, because the oar's weight is on the gunwale. Therefore, it is the balance that makes oars feel lightweight. Leathering the oars is a project as well as sealing and varnishing. Everybody left with the oars largely done. One student had a good challenge. He brought in a pair of hollow sculling oars and wanted to make a replacement (or back up) pair in a week. So, we made the loom solid, sized down, and laminated a pair or plywood blades much like I do in my shop for customer's oars, over a laminating jig. The blades are glued on the shaped loom and the finished result looks like this, and I might add he is very happy with them. In fact they are no heavier than the original, hollow sculls!